濟南模具加工是塑料加工工業中和塑料成型機配套，賦予塑料制品以完整構型和精確尺寸的工具。由于塑料品種和加工方法繁多，塑料成型機和塑料制品的結構又繁簡不一，所以濟南模具加工的種類和結構也是多種多樣的。那么，我們在設計濟南模具加工時，都需要注意哪些要點呢？Ji'nan mold processing is the plastic processing industry and plastic molding machine, plastic products to complete configuration and precise size tools. Because of the plastic varieties and processing methods of various plastic molding machine and plastic product structure is simplified, so Ji'nan mold type and structure is various. So, we in the design of Ji'nan mold processing, need to pay attention to what points?

1.開模方向。濟南塑料模具的開模方向確定后，可選擇適當的分型線，避免開模方向存在倒扣，以改善外觀及性能。濟南塑料模具的開模方向確定后，產品的加強筋、卡扣、凸起等結構盡可能設計成與開模方向一致，以避免抽芯減少拼縫線，延長模具壽命。Opening direction. Ji'nan plastic mold after the mold direction is determined, you can choose the appropriate parting line, to avoid the opening direction of the existing button to improve the appearance and performance. Ji'nan plastic mold parting direction, product rib, buckle, convex structure as much as possible consistent with the direction of mold design, in order to avoid pulling reduce joint line, prolongs the service life of the mould.

2.產品壁厚。濟南模具加工的壁厚不均會引起氣孔和熔接痕。濟南塑料模具的壁厚不均會引起塑膠產品表面縮水。各種塑料均有一定的壁厚范圍，一般0.5~4mm，當壁厚超過4mm時，將引起冷卻時間過長，產生縮印等問題，應考慮改變產品結構。Product wall thickness. The uneven thickness of the die in Ji'nan will cause the pores and the weld marks. The uneven thickness of plastic mold in Ji'nan will cause the shrink of plastic products. All kinds of plastic has a certain thickness range of 0.5~4mm, when the wall thickness is more than 4mm, will cause the cooling time is too long, which reduce and other issues, should consider changing the product structure.

3.扣位。將濟南模具加工的扣位裝置設計成多個扣位同時共用，使整體的裝置不會因為個別扣位的損壞而不能運作，從而增加其使用壽命，再是多考濾加圓角，增加強度。濟南塑料模具的扣位相關尺寸的公差要求十分嚴謹，倒扣位置過多容易形成扣位損壞；相反，倒扣位置過少則裝配位置難於控制或組合部份出現過松的現象。解決辦法是要預留改模容易加膠的方式來實現。Buckle position. Ji'nan mold locking device design into a plurality of buckling and sharing, so that the overall device will not buckle because individual bit damaged and not operation, thereby increasing its service life, and is admitted to filter radius, increase strength. Ji'nan plastic mold buckle a size tolerance requirements are very strict, inverted position too easy to form buckling damage; on the contrary, the inverted position is too difficult to control the assembly position or combination part appeared loose phenomenon. The solution is to modify the mold to be easy to add glue to achieve.

4.脫模斜度。濟南模具加工廠家認為，適當的脫模斜度可避免產品拉毛(拉花)。光滑表面的脫模斜度應該小于0.5度，細皮紋(砂面)表面大于1度，粗皮紋表面大于1.5度。適當的脫模斜度可避免產品頂傷，如頂白、頂變形、頂破。深腔結構產品設計時外表面斜度盡量要求大于內表面斜度，以保證注塑時模具型芯不偏位,得到均勻的產品壁厚，并保證產品開口部位的材料強度。Stripping slope. Ji'nan mold processing factory, draft the appropriate products to avoid picking (Garland). The smooth surface should be less than 0.5 degrees, and the fine grain (sand) surface is more than 1 degrees, and the coarse grain surface is more than 1.5 degrees. Appropriate stripping slope can avoid the product top injury, such as top white, top deformation, top broken. In the design of the deep cavity structure, the external surface slope should be greater than the inner surface slope, so as to ensure that the die core is not biased, and the uniform product thickness is obtained.